theben theLeda S8-100 WH LED Spotlight with Motion Detector Instruction Manual
Contents
Basic safety information
Assembly and installation should only be carried out by a qualified electrician, somebody who has completed appropriate professional training and has the knowledge and experience necessary to be able to recognise and avoid the potential dangers posed by electricity.
Before installation/disassembly, disconnect the power supply and ensure that the parts are no longer live.
Prior to start-up and using the product, read and observe the operating instructions.
Only intended for installation out of arm‘s reach.
The LED spotlight with motion detector (PIR) conforms to EN 60598-1 and EN 60669-2-1 if correctly installed.
Optional with corner angle (9070969/907098 and distance frame (9070971/9070988).
Proper use
- LED spotlight is used for lighting, depending on presence and brightness
- Device is for wall mounting inside and outside
- For entrances, garages, gardens, corridors, parks, etc.
Lamp cannot be replaced.
Replace entire spotlight if defective!
Connection
Secure device with an upstream type B or type C circuit breaker (EN 60898-1) with a maximum of 10 A.
Standard connection
Master/Slave connection
Max. 8 devices switchable as Master/Slave!
Master/Master connection
Time delay with master/master switching
If the devices are switched on via port L ↓ the time delay of the triggered device applies to all connected devices.
Time delay of 10 s at master 1
Time delay of 20 s at master 2
If several devices simultaneously fulfil the conditions for motion and brightness, all masters remain switched on, as long as a time delay elapses.
If several masters meet brightness and motion conditions consecutively, all time delays will elapse individually, the last time delay will leave all devices switched on.
Installation
Installation instructions
Observe the recommended installation height of 1.8 m–2.5 m!
As the motion detector responds to variations in temperature, avoid the following situations:
Do not point the device at objects with highly reflective surfaces such as mirrors or glass surfaces.
Do not install the LED spotlight near heat sources, such as heating outlets, air conditioning systems, lamps etc.
Do not direct the LED spotlight at objects that move in the wind, such as curtains, large plants etc.
Pay attention to the direction of motion during the test run.
- Disconnect power source.
- Use spacer (9070971/9070988) or corner angle (9070969/9070987) (optional).
- Loosen catch mechanisms with a screwdriver and remove LED spotlight from base.
- Make marks for the holes and drill the holes.
- Guide wire through the socket‘s seal; fix socket to the wall.
- Fix socket to wall, connect the individual wires to the appropriate terminal and tighten screws.
- Place and engage the LED spotlight on the base.
- Connect LED spotlight to mains.
The warm-up phase of the device takes approx. 40 s.
During this time, the light is switched on.
Description
The device has 2 potentiometers for setting time and brightness.
Settings
The potentiometer settings will be adopted 15 s after the light has gone out.
Setting the brightness
- Turn the potentiometer towards „Moon“; the LED spotlight only switches on when it is relatively dark.
- Turn the potentiometer towards „Sun“; the LED spotlight switches on when it is relatively bright.
- Turn the potentiometer to „Sun“, and the device works independent of brightness.
Setting the time
- Set the potentiometer to the desired time (10 s–30 min).
Manual operation
The lighting can be switched on manually via a circuit breaker button.
A circuit breaker button must be connected.
Function only possible at night.
- Quickly confirm Circuit breaker 2 x (within 2 s).
▻ The lighting remains switched on for 6 hours. - To switch off the lighting and return to auto mode, press the circuit breaker briefly (within 2 s).
- If the circuit breaker is pressed x2 during this six second turn-on time, the lighting is switched on again for 6 hours.
Walking test
The walking test is used to test the detection area and to restrict it if necessary.
- Set potentiometer „brightness“ to „sun“.
- Turn the “time” potentiometer counterclockwise up to the stop.
▻ The motion detector now always reacts to movements (independent of brightness). - Walk through the detection area at a right angle. After the motion detector has detected a movement, it switches on for 2 s.
Pay attention to the direction of motion during the test.
Aligning the LED spotlight
theLeda S8-100
theLeda S17-100
Limiting the detection area
- Use enclosed stickers to adjust the motion detector to the desired detection area.
- Remove the required section of the sticker by using scissors.
- Then stick to the lens.
Technical Data
Cleaning and service
- Only use a dry, soft cloth to clean the device surface.
- Do not use any cleaning agents or solvents.
Disposal
- Dispose of device in environmentally sound manner (electronic waste).
Contact
Theben AG
Hohenbergstr. 32
72401 Haigerloch
GERMANY
Phone +49 7474 692-0
Fax +49 7474 692-150
Hotline
Phone +49 7474 692-369
[email protected]
Addresses, telephone numbers, etc.
www.theben.de