SATCO 65-710 Bullet Head Security Lights Instruction Manual

Home » SATCO » SATCO 65-710 Bullet Head Security Lights Instruction Manual

LED DUAL HEAD
SECURITY LIGHTSATCO 65 710 Bullet Head Security LightsModels: 65/710, 65/712, 65/714, 65/716, 65/718, 65/720
Models with Optional Motion Sensor: 65/711, 65/713, 65/715, 65/717, 65/719, 65/721

INSTALLATION AND SAFETY INSTRUCTIONS

IMPORTANT: Read before installing fixture. Retain for future reference.

WARNING: Risk of Fire or Electric Shock

  • Commercial installation, service and maintenance of luminaries should be performed by a qualified licensed electrician. If you are unsure about the installation or maintenance of the luminaries, consult a qualified licensed electrician and check your local  electrical code.
  • Turn OFF power at fuse or circuit breaker before wiring fixture to power supply.
  • Turn OFF power when you perform any maintenance.
  • Verify that supply voltage is correct by comparing it with the luminaire label.
  • Risk of Burn. Disconnect power and allow fixture to cool before handling.
  • Clean glass lens with non-abrasive glass cleaning solution.
  • Do not open fixture to clean the LED. Do not touch the LED.

WIRING: If wiring does not include a ground wire, consult your local electrical code for approved grounding methods. For proper connection, place wire nut over wires and twist clockwise until tight.

  1. Connect supply wires. Use wire nut to connect the black fixture wire to the black power supply wire and the white fixture wire to the white (neutral) supply wire.
    NOTE: Lamp heads must be positioned above motion sensor head and controls on motion sensor  must face the ground.
  2. Aim lamp heads and install optional visors. Loosen knobs and aim lamp heads.
    CAUTION: Risk of Shock: Aim lamp heads at least 20º down below horizontal in order to prevent water from accumulating inside lens. After lamp heads are positioned as desired, align the optional visor over the front of the lamp head and secure by  tightening set screw on visor.
  3. Weatherproof gaskets and junction box with silicone sealant, tighten all screws.

SATCO 65 710 Bullet Head Security Lights - SensorSATCO 65 710 Bullet Head Security Lights - DIAGRAM

INSTALLATION: Wall Mount (External Junction Box)

STEP 1: Disconnect power supply.
Remove (2) plastic plugs. Remove inserted screws and mounting plate.
SATCO 65 710 Bullet Head Security Lights - STEP 1STEP 2: Attach junction box on
the wall (not supplied).SATCO 65 710 Bullet Head Security Lights - wallSTEP 3: Fix mounting plate and gasket onto junction box.SATCO 65 710 Bullet Head Security Lights - boxSTEP 4: Connect the wires, refer to the Wiring Diagram.SATCO 65 710 Bullet Head Security Lights - Wiring DiagramSTEP 5: Secure fixture onto mounting plate with screws, replace plastic plugs.SATCO 65 710 Bullet Head Security Lights - screwsSTEP 6: Check fixture and connect power supply.SATCO 65 710 Bullet Head Security Lights - power supplyINSTALLATION: Wall Mount (Built-in Junction Box)

STEP 1: Disconnect power supply.
Remove (2) plastic plugs. Remove inserted screws and mounting plate.SATCO 65 710 Bullet Head Security Lights - mounting plateSTEP 2: Drill (4) holes on the wall and insert expansion screws. Attach gasket and fix mounting plate with screws.SATCO 65 710 Bullet Head Security Lights - with screwsSTEP 3: Connect the wires, refer to the Wiring Diagram.SATCO 65 710 Bullet Head Security Lights - the Wiring DiagramSTEP 4: Secure fixture onto mounting plate with screws.SATCO 65 710 Bullet Head Security Lights - mounting 2STEP 5: Replace plastic plugs.SATCO 65 710 Bullet Head Security Lights - plugsSTEP 6: Check fixture and connect power supply.SATCO 65 710 Bullet Head Security Lights - fixture

INSTALLATION: Ceiling Mount

STEP 1: Disconnect power supply.
Remove (2) plastic plugs. Remove inserted screws and mounting plate.SATCO 65 710 Bullet Head Security Lights - Ceiling Mount 1STEP 2: Attach junction box on the wall (not supplied).SATCO 65 710 Bullet Head Security Lights - Ceiling Mount 2STEP 3: Fix mounting plate and gasket onto junction box.SATCO 65 710 Bullet Head Security Lights - Ceiling Mount 3STEP 4: Connect the wires, refer to the Wiring Diagram.SATCO 65 710 Bullet Head Security Lights - Ceiling Mount 4STEP 5: Secure fixture onto mounting plate with screws, replace plastic plugs.SATCO 65 710 Bullet Head Security Lights - Ceiling Mount 5STEP 6: Check fixture and connect power supply.SATCO 65 710 Bullet Head Security Lights - Ceiling Mount 6

TROUBLESHOOTING

  1. Check your power source.
  2. Check electrical connections.
  3. Check that the photocell or motion sensor is working properly (if so equipped).

Leave a Comment