IMC40
Banknote Counter
Maintenance Manual
Version 1.00
Contents
How to disassemble machine
Notice:
When you receive the package, open and check the packing list in the package.
Disassemble left side cover step by step as following:
Disassemble right side cover step by step as following:
Disassemble display step by step as following:
Disassemble mainboard step by step as following:
Disassemble detection table step by step as following:
Take the transit table step by step as following:
Disassemble the build-in printer step by step as following:
Machine explosive
Whole machine explosive
Feeding block part set
Front guide set
Front path guider set
Back path guide set
Detection tabel
Transit tabel
Menu Instruction
Press MENU to enter
Service Menu introduction, password: 6666
External device:
Encoder Value:
 |
Sensor Adjustment:
 |
Calibrate the reject pocket sensor value by press the Enter key. |
Password Set:
 |
CIS & Motor Aging:
 |
Enter to start aging test, and also to check the electronic magnetic function once BC error happens |
Total Counted:
 |
 Be careful with this function, it will clear the total counted pieces record and can not get it back. |
Image Data Save Set:
 |
1. Save counted image (save all image that counted) 2. Save OCR image (save serial number image only) 3. Save error image (save the image that machine gives error) |
Image Data View:
 |
To check the image data if has problem |
MT MG Waveforms
 |
To check the MG wave of the notes |
Detection Level:
 |
Adjust the detection sensitive accordingly |
Fitness Set:
 |
Set the fitness detection level sensitive accordingly |
Baud Rate Set:
 |
To set the baud rate to match with external printer or display accordingly |
Restore Factory Set:
 |
Be careful with this function, it will reverse all set back to factory set |
Common Issue reference
Feeding issue
| Problem Description : | Machine happens feeding hardly, double error, chain error, skew error, jam issue, miss counted |
| Reason: | Feeding gap is not in a properly distance |
| Solution : | Adjust the feeding gap to the properly distance as following picture shows |
Electromagnetic issue
| Problem Description: | 1. Machine happens BC error 2. jam issue 3. PS2 4.PS3 |
| Reason: | Electromagnetic reaction problem |
| Solution: | 1. Check the shelf holder of electromagnetic if loosen 2. Check the electromagnetic itself can be movable 3. The plastic of toggle bill part if change of shape during using |
Display issue
| Problem Description : | 1. Machine display happens splash screen 2. white screen or no response when touching it The count remain 0 during counting |
| Reason : | 1. Display itself problem 2. Display board has unsolder problem 3. Mainboard problem |
| Solution : | 1. Replace the display 2. Replace the display board 3. Replace mainboard |
Mainboard issue
| Problem Description : | 1. Machine display happens splash screen 2. CIS calibration failed 3. Too much error happen 4. Mainboard error S. Machine doesn’t count |
| Reason : | Mainboard chip damaged or unsolder problem |
| Solution : | Replace the mainboard |
CIS issue
| Problem Description : | 1. All notes rejected 2. CIS calibration failed |
| Reason : | CIS or CIS cable damaged |
| Solution : | Replace CIS |
Error list& Trouble shooting
Feeding issue
| ERROR | REASON |
| El: UV Error | Note doesn’t have UV |
| EZ Double Error | Double or Multi notes passed together |
| E3:Chain Error | Double or Multi notes counted in chain |
| E4:Skew Error | Note counted skewed too much |
| ES: Full | Reject pocket or Stacker full |
| E6: Half note Error | The note is not complete |
| Interval Error | The distance between two notes passed by is too short |
| Width Error | The width of note incorrect |
| Signal T Error | Signal transport problem |
| Data Process Error | Data processing over time limit |
| Denomination Error | Denomination don’t match with count set |
| Image Error | Counterfeit or Data recognize problem |
| Face Error | Face of note doesn’t match with count set |
| Orientation Error | Orientation of note doesn’t match with count set |
| DOI Error | Date of Issue for note doesn’t match with count set |
| Version Error | Version of note doesn’t match with count set |
| MT Error | Note has magnetic problem |
| MT2 Error | Note has magnetic problem |
| MG1 Error | Note has magnetic problem |
| MG2 Error | Note has magnetic problem |
| MG3 Error | Note has magnetic problem |
| MG4 Error | Note has magnetic problem |
| S.Skew Error | Super skew of note |
| IR Error | Note has IR (transmit and reflection)problem |
Fcc caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Contact us
Scan the QR code for Facebook and WhatsApp online chat
 |
 |
https://www.facebook.com/munbyn/ |
https://wa.me/qr/UTUXFZQZF2LHA1 |
Email: [email protected] (24-7 online support)
Website: www.munbyn.com (how-to videos, warranty details)
WhatsAPP: +86 18144898200
Skype: + 1650 206 2250
MUNBYN provides 18 months warranty and lifetime free service. If you encounter any issues with the product, please contact the MUNBYN team to promptly receive troubleshooting
tips or a replacement.
MORE CHOICE FOR YOUR
GROWING BUSINESS