MiBOXER 150W 5in1 Wi-Fi LED Controller Instruction Manual

MiBOXER 150W 5in1 Wi-Fi LED Controller 

Product features

This product uses WiFi + Bluetooth + 2.4G wireless transmission technology, low power consumption, strong anti-interference ability. WiFi + Bluetooth connect network can greatly enhance the connect network experience. When the router is disconnected, Bluetooth can also directly connect and control equipment at close range.
After successful network configuration using [Tuya Smart] app to achieve wireless dimming, remote control, group control, scene control, timing control, music movement, biorhythm, sleep plan, wake plan, one key execution, automation, etc. functions. And it supports 2.4G remote control.

16 Millions of colors

to choose Color temperature adjustable

Dim brightness Saturation

2.4G RF wireless transmission technology

WiFi wireless control support long-range control

Auto-transmitting & Synchronization (only for remote control dimming)

Device sharing

Tap-to-Run & automation

Timing setting / countdown turn on / off LED light

DMX512 controllable (Only for RGB+CCT output mode DMX512 LED transmitter is needed)

Remote control Control distance 30m

Smartphone app control

Support third party voice control

Group control

Biorhythm

Support music rhythm

Sleep / wake up plan

Support scene customization

Do not disturb mode

Waterproof and dustproof grade IP67

Setting Output Mode

Set up correct output mode based on the feature of lights

Group Button	Zone 1	Zone 2	Zone 3	Zone 4	Zone 5 / Master ON
Output Mode	Single color	Dual white	RGB	RGBW	RGB+CCT

Method 1: Remote sets output mode (Note: If there is no operation within 10 seconds, it will automatically exit).

1. Long press “ON” button or group “ I ” 10 seconds until light flashes slowly.
2. Press group button “ I ”to switch the corresponding output mode.

Setting output mode only supports 4 or more than 4 Zones remote

Method 2: Setting output mode by Tuya App Need to pair network before setting, please check (9 page) for more details.

1. Click on the ” Common Functions ” of the corresponding device
2. Click on ” Output Mode “
3. Select the corresponding output mode
   

PUSH Dimming

Short press PUSH switch:
Turn ON/OFF light
Long press PUSH switch:

• Steeples dimming brightness.
• Long press and release your finger, then repeat long pressing to increase or decrease brightness.
  

Compatible with these 2.4G RF remote controls (Purchased separately)

• FUT100
  
• FUT089S
  
• FUT089 FUT089-B
  
• FUTOSS
  
• FUT092 FUT092-B
  
• FUT096 FUT096-B
  
• FUT007
  
• BO I B0-B
  
• B1 /B1-B/T1
  
• B2 /T2
  
• K1 /K1-B
  
• B3 I B3-B I T3
  
• BB
  
• B4/B4-B/T4
  
• S1-B/S1-W S1-G
  
• S2-B/S2-W S2-G
  
• FUTD01
  

2.4G RF Remote control instruction

Linking Code Instructions

1. Power off 10 seconds and power on again or turn on light via PUSH switch
   
2. Short press ” I ” button 3 times within 3 seconds.
   
3. Lights blink 3 times slowly means linking is done successfully.
   

Linking failed if light is not blinking slowly, Please follow above steps again. (Note: Light that have linked can’t link again)

Unlinking Code Instructions

1. Power off 10 seconds and power on again or turn on light via PUSH switch
   
2. Short press ” I ” button 5 times within 3 seconds.
   
3. Lights blink 10 times quickly means unlinking is done successfully
   

Unlinking failed if light is not blinking quickly, Please follow above steps again.
(Note: Light haven’t linked that don’t need to unlink)

Auto transmitting & Synchronization (only for remote control) Remote signal auto transmitting

One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.
Dynamic modes auto synchronization
Multi lights can synchronize if they are in same dynamic mode and linked with same remote (distance between each light is within 30m)

Dynamic mode table selection (only for remote control) 

Select dynamic mode table 1:

While the light is in static mode, short press” S+” button 5 times quickly until blue light fiashes 3 times slowly, static mode is activated successfully.

Select dynamic mode table 2:

While the light is in static mode, short press” S-” button 5 times quickly until yellow light fiashes 3 times slowly, static mode is activated successfully.

Dynamic mode table 1 (default)

Number	Dynamic Mode	Brightness/ Saturation/ Speed
1	Mardi Gras	Adjustable
2	Automatic color change
3	Sam
4	Gemstone
5	Twilight
6	American
7	Fat Tuesday
8	Party
9	Slow Color Splash

Dynamic mode table 2 (need to switch manually)

Number	Dynamic Mode	Brightness/ Saturation / Speed
1	Seven colors gradual change	Adjustable
2	White light Gradual change
3	RGB gradual change
4	Seven colors jump to change
5	Jump to change randomly
6	Red light gradual change +Flash 3 times
7	Green light gradual change +Flash 3 times
8	Blue light gradual change +Flash 3 times
9	White light gradual change +Flash 3 times

“Do Not Disturb” mode is activated and shut down (default activated)

Turn on “Do Not Disturb” mode (wide using in the area which have power failure frequently to save energy)

2.4G RF Remote turn on and turn off instruction

Turn on “Do Not Disturb” mode:

Press “OFF” button three times within three seconds and press “ON” button three times, Activated successfully once led light fiashes four times quickly.

Attention: Do not disturb mode is activated

1. When the light is OFF status (For example: Use app or remote to turn off light) The light is OFF status once you turn off power and turn on again.
   (User must turn off and turn on power twice times to activate light or use APP/ remote to activate light)
2. When the light is ON status The light is ON status once you turn off and turn on power one time.

Turn off “Do Not Disturb” mode:

Press “ON” button three times within three seconds and press “OFF” button three times, closed successfully once led light fiashes four times slowly.
Attention: The light will be always “ON” status if you turn on and turn off power once user closed “Do Not Disturb” mode.

App turn on and off “Do Not Disturb” mode instruction (check details in page 91)

Smartphone APP control instruction

Network Configuration (Don’t support 5G router)

1. Download and install [Tuya Smart] app Search for [Tuya Smart] in Apple or Google store or scan following QR code to download and install the app.
   Please open the app click ” Register” button to create account while using it in the first time, Log in directly if you already had account.
   
2. Network Configuration
   1. Connect controller with power supply.
   2. Confirm light is fiashing quickly (2 flashes per second), If the light is not in the fast flashing state, the method to enter the fast flashing state is as follows:
      • Power off and on controller 3 times.
   3. Connect phone with home WiFi network in the 2.4GHz frequency.
   4. Open homepage of app and click”+” button at the upper right corner of page
   5. Click” Lighting” on the left side of page and then click” Light Source {BLE+Wi-Fi)”
   6. Follow app prompts to complete configuration.
      

App turn on and off “Do Not Disturb” mode (default activated)

Click the light which need to be set up or group control — click “More” — click “Power-on behavior” -turn on or off

Alexa voice control instruction

Please add device into [Tuya Smart] app (check details in page 9), then start following steps

1. Open Alexa App
2. Click “More” on the bottom of right corner
3. Click “Skills & Games”
   
4. Click “” on the top of right corner
5. Type into “Smart life” and search
   
6. Click “Smart Life” skill, follow instruction to finish configuration and start voice control
   

Google Home voice control instruction

Please add device into [Tuya Smart] app (check details above), then start following steps

1. Open Google Home App
2. Click”+” on the top of left corner
   
3. Click “Set up device”
   
4. Click “Works with Google”
   
5. Click” 0.” on the top of right corner
6. Type into “Smart life” and search
7. Click “Smart Life” skill, follow instruction to finish configuration and start voice control
   

DMXS12 LED Transmitter Control (Purchased separately)

Only for RGB+CCT output mode

DMX512 LED Transmitter Link/Unlink

(1)Follow instruction of DMX512 transmitter (FUTD01), Choose the zone for the light by pressing “+ 11 or” – ” (e.g. 11CH12″ means zone 12)

Link

Power off 10 seconds and power on again or turn on light via PUSH switch

Short press 11” 5 times within 3 seconds while the light of controller is ON

Link is done once light of controller flashes 3 times slowly

Unlink

Power off 10 seconds and power on again or turn on light via PUSH switch

Short press 5 times within 3 seconds while the light of controller is ON

Unlink is done once light of controller fiashes 10 times quickly

If the link or unlink failed, please follow the above steps again.

Connect to LED strip diagram

Controller input voltage must be in accordance with the required voltage of LED Strips.

Single Color Mode

Dual White Mode

RGB Mode

RGBW Mode

RGB+CCT Mode

Instruction

Attention

1. Please turn off power supply before installation.
2. Please ensure input voltage to be same as requirements from device.
3. Don’t disassemble device if you are not expert, otherwise it will damage it.
4. Please do not use the light in the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.

Made in China