MCHOSE G11 Gaming Headset User Manual

MCHOSE G11 Gaming Headset

FAQ

Frequently Asked Questions

• Q: How do I troubleshoot connectivity issues with the headset?
  • A: If you experience connectivity problems, try reorienting the receiving antenna, increasing separation from other devices, or consulting a technician for assistance.
• Q: What should I do if the headset does not power on?
  • A: Ensure the headset is charged or connected to a power source. Press and hold the power button until the indicator light turns on.

KEY DIAGRAM

SPECIFICATIONS AND PARAMETER

SPECIFICATIONS

• Battery capacity: 500mAh
• Charging time: About 1.5H
• Charging port: TYPE-C USB
• Connection range: > 10m
• Size: 172.8*80.5*179.4 mm
• weight: About 188g

PARAMETER

• Speaker Spec: $40mm
• Rating: 15mW
• Sensitivity: 1013dB
• Frequency response: 20Hz~20KHz
• Mic Spec: 46*2.7mm
• Rated voltage: 3.0V
• Sensitivity: -38$3dB
• Frequency response: 100Hz~10000KHz

LED INDICATOR

CONNECTION STEP

Bluetooth connection 

• While in Bluetooth mode, the blue light flash fast and wait for pairing, accompanied with “power-on,pairing” prompt tone. .
• Open Bluetooth and search “G11″ on your mobile, the indicator stop flash and keep burning, accompanied with ” connected” prompt tone. It will reconnect automatically next time.

2.4G connection

While in 2.4G mode, press power button 3 seconds until hear “pairing” prompt tone, then insert the dongle into PC, the white light on dongle and green light on headset keeps burning that the headset is paired. It will reconnect automatically next time, if dongle is insert into PC.

Wired connection

• While in power on, insert the line in cable (type-c to 3.5mm),the headset will auto off and enter Wired mode. The button and volumer will in non-function state while in this mode.
• The mode at start up is same as headset be shut down last time

OPERATING INSTRUCTION

1. Power on: Press Power button 3 seconds, the blue light for Bluetooth mode, white light for 2.4G slow flash wait for pairing, accompanied with ” power-on” prompt tone.
2. Power off: While inpower-on, press power button3 seconds, the Indicator flash twice and goesoff, accompanied with ” power off” tone.
3. BT/2.4G switch: while in paring, press mic button 3 seconds to change mode, Bluetooth with Blue light and 2.4G with white light, accompanied with prompt tone.
4. EQ: While in paring, click EQ button to change sound effect, the indicator on, accompanied with ” Game mode” or”Music mode” prompt tone.
5. Microphone: While in paring, click mic button to open or close the mic, accompanied with “Mic on” or “Mic off” prompt tone.
6. Volume +/- : While in listing or calling, slide the volumer to control the volume.
7. Phone calls: While in standby or multi-media mode, press power button or using mobile answer key to answer the calls.
8. Hang up: While on calling, short press power button to hang up.
9. Reject call: While in incoming call, long press power button to reject calls.

ATTENTION

1. Don’t break the headset, like knock,strike, drop,warping or put it into water, and disassemble also.
2. Please keep the headset off the magnetic field and wet air, usage temperature (-10°Cto 40°C).
3. Don’t clean the headset with using corrosive liquid.
4. Avert reduce the battery lift, please don’ t overcharge and place in the environment with dry, Room temperature, clean if not use for a long time.
5. Please charge-discharge once in a while to make the battery keep good performance.

WARRANTY CARD

• User name: …………………………
• Model no. …………………………
• User’s address and email address: …………………………
• Date of purchase: …………………………
• Distributor name: …………………………
• Distributor telephone: …………………………

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.