JBC GSF Guide Kits
Contents
Introduction
This manual corresponds to the following references:
With Solder Wire Perforation:
GSF08V-B for wire Ø 0.8 mm / Ø 0.032 in
GSF10V-B for wire Ø 1.0 mm / Ø 0.040 in
GSF12V-B for wire Ø 1.2 mm / Ø 0.047 in
GSF15V-B for wire Ø 1.5 mm / Ø 0.059 in
GSF16V-B for wire Ø 1.6 mm / Ø 0.063 i
Without Solder Wire Perforation:
GSF04D-B for wire Ø 0.38 – 0.40 mm / Ø 0.015 – 0.016 in
GSF05D-B for wire Ø 0.46 – 0.56 mm / Ø 0.018 – 0.022 in
GSF06D-B for wire Ø 0.60 – 0.64 mm / Ø 0.023 – 0.025 in
GSF07D-B for wire Ø 0.70 – 0.78 mm / Ø 0.028 – 0.031 in
GSF08D-B for wire Ø 0.80 – 0.82 mm / Ø 0.032 – 0.033 in
GSF10D-B for wire Ø 0.90 – 1.10 mm / Ø 0.036 – 0.044 in
GSF12D-B for wire Ø 1.14 – 1.27 mm / Ø 0.045 – 0.051 in
GSF15D-B for wire Ø 1.50 – 1.57 mm / Ø 0.060 – 0.062 in
GSF16D-B for wire Ø 1.60 – 1.63 mm / Ø 0.063 – 0.065 in
GSF18D-B for wire Ø 1.80 mm / Ø 0.073 in
GSF Guide Kit for SF280 with Solder Wire Perforation
Packing List
The following items are included:
Guide Tube* ……………………………………… 1 unit
Inlet Nozzle* ……………………………………… 1 unit
Guide Wheel* ……………………………………. 1 unit
Counter Wheel* ………………………………… 1 unit
Blade Clamp* ……………………………………. 1 unit
Blade* ………………………………………………… 1 unit
Intermediate Nozzle* ……………………….. 1 unit
Outlet Nozzle* …………………………………… 1 unit
*references see table on page 4
Allen Screws* ………………………………….. 2 units
Headless Screws* ………………………….. 3 units
Manual ………………………………………………. 1 unit Ref. 0028099
GSF Guide Kit for SF280 without Solder Wire Perforation
Packing List
The following items are included:
Guide Tube* ……………………………………… 1 unit
Inlet Nozzle* ……………………………………… 1 unit
Traction Wheel* ………………………………… 1 unit
Support Wheel* ………………………………… 1 unit
Counter Wheel* ………………………………… 1 unit
Intermediate Nozzle* ……………………….. 1 unit
Outlet Nozzle* …………………………………… 1 unit
*references see table on page 5
Allen Screws* ………………………………….. 2 units
Headless Screws* ………………………….. 3 units
Manual ………………………………………………. 1 unit Ref. 0028099
GSF Guide Kit for SF280 with Solder Wire Perforation
|
Outlet nozzle |
Nozzle | Guide wheel | Blade | Blade clamp | Inlet nozzle | lantern. nozzle | Counter wheel | Screws |
Threaded stud |
|
|
|
||||||||||
|
GSF08V-B |
0025270 | 0021158 | 0021696 | 0021555 | 0018638 | 0018632 | 0024955 | 0026693(Supplied with SF) | 0026695 (x2) | 0026696 (x3) |
| GSF10V-B |
0021560 |
0021699 |
0019170 |
0024956 |
0026694 |
|||||
|
GSF12V-B |
0025272 | 0023738 | 0019171 | 0024957 | ||||||
| GSF15V-8 |
0025274 |
0019696 |
0024958 |
|||||||
|
GSF16V-B |
0025276 |
0025922 |
0024233 |
0024959 |
GSF Guide Kit for SF280 without Solder Wire Perforation
|
|
OuUet nozzle | Nozzle | Nozzle wheel | Support wheel | Support wheel | Support wheel | Support wheel | Screws |
Threaded stud |
|
|
|||||||||
|
GSF04D-B |
0025268 | 0021158 | 0019479 | 0020345 | 0019520 |
0024954 |
0026693 (Supplied with SF) |
0026695 (x2) | 0026696 (X3) |
|
GSFOSD-B |
|||||||||
| GSF06D-B | 022994 | 0019519 |
0025293 |
||||||
|
GSF07D-B |
0025289 |
0018632 |
0025291 |
||||||
| GSFOBD-B | 0025270 | 0019480 |
0024955 |
||||||
|
GSF10D-B |
0021560 | 0019170 | 0024956 | ||||||
| GSF12D-B |
0025272 |
0019481 |
0019171 | 0024957 | 0026694 | ||||
|
GSF15D-B |
0025274 | 0024958 | |||||||
| GSF16D-B |
0025276 |
0028367 |
0024233 |
0024959 |
|||||
|
GSF18DB |
002155–9 |
0024234 |
0024960 |
Changing Guide Kits
Changing Wheels and Blade
For this operation, disconnect the device from the mains. Disconnect the tool from the control unit and open its cover.
First disassemble the guide tube (6), the nozzles (2)+(3), then the wheels, blade and clamp (4)+(5).
Disassemble the counter wheel (1). Use the alien key and the spanner, provided with the station.
Assembly with Solder Wire Perforation:
Assemble the counter wheel (1).
Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
Assemble the inlet nozzle (3).
Assemble the guide wheel (4) and tighten the screw.
Assemble the blade first, then mount the blade clamp (5) onto the same axis and tighten the screw. Caution: handle the blade carefully to avoid injury.
Insert the guide set (6).
Assembly without Solder Wire Perforation:
Assemble the counter wheel (1).
Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
Assemble the inlet nozzle (3).
Assemble the support wheel* (4) onto the axis and tighten the screw.
Assemble the traction wheel (5) and tighten the screw.
Insert the guide set (6).
wheel bears diameter marking
Replacing the Guide Tube
Once the tool is disconnected from the control unit follow the instructions below:
Disassemble the outlet nozzle (1) from the guide tube.
Open the guide clamp (2), take off the guide tube (3) and insert the new one.
Note: The guide tube length can be easily adjusted (4) when the guide clamp knob (2) is open.
Once the guide tube length is adjusted close the guide clamp knob (2).
Assemble the outlet nozzle (1) onto the guide tube tip.
Enter en “Tool Settings” at the SF control unit main menu and select the proper wire diameter.
SF with Guide Tube assembled
SF with no Guide Tube assembled
Tool Assembly
Connect the tool to the control unit following this steps:
Insert and push the guide nozzle until the end
(1) and tighten the screw (2). Connect the jack (3).
Solder Wire Loading
Put the solder reel into its support (1).
Introduce the solder wire into the inlet nozzle (2) until it reaches the wheels (3).
Use the Tin Reload Process in the Main Menu (4)
The Relaod Procees screen opens.
Press 
to start the process.
Make sure the wire passes through the Intermediate Nozzle and enters into the Guide Tube (5).
Specifications
GSF Guide Kits for SF280
| With Perforation: | Total Net Weight: | Package Weight: |
| Ref.: GSF08V-B wire Ø 0.8 mm / Ø 0.032 in | 108 g / 0.24 lb | 200 g / 0.44 lb |
| Ref.: GSF10V-B wire Ø 1.0 mm / Ø 0.040 in | 108 g / 0.24 lb | 200 g / 0.44 lb |
| Ref.: GSF12V-B wire Ø 1.2 mm / Ø 0.047 in | 94 g / 0.21 lb | 186 g / 0.41 lb |
| Ref.: GSF15V-B wire Ø 1.5 mm / Ø 0.059 in | 94 g / 0.21 lb | 186 g / 0.41 lb |
| Ref.: GSF16V-B wire Ø 1.6 mm / Ø 0.063 in | 94 g / 0.21 lb | 186 g / 0.41 lb |
| Without Perforation: | ||
| GSF04D-B for wire Ø 0.38 – 0.40 mm / Ø 0.015 – 0.016 in | 104 g / 0.23 lb | 196 g / 0.43 lb |
| GSF05D-B for wire Ø 0.46 – 0.56 mm / Ø 0.018 – 0.022 in | 104 g / 0.23 lb | 196 g / 0.43 lb |
| GSF06D-B for wire Ø 0.60 – 0.64 mm / Ø 0.023 – 0.025 in | 104 g / 0.23 lb | 196 g / 0.43 lb |
| GSF07D-B for wire Ø 0.70 – 0.78 mm / Ø 0.028 – 0.031 in | 104 g / 0.23 lb | 196 g / 0.43 lb |
| GSF08D-B for wire Ø 0.80 – 0.82 mm / Ø 0.032 – 0.033 in | 104 g / 0.23 lb | 196 g / 0.43 lb |
| GSF10D-B for wire Ø 0.90 – 1.10 mm / Ø 0.036 – 0.044 in | 90 g / 0.20 lb | 182 g /0.40 lb |
| GSF12D-B for wire Ø 1.14 – 1.27 mm / Ø 0.045 – 0.051 in | 90 g / 0.20 lb | 182 g /0.40 lb |
| GSF15D-B for wire Ø 1.50 – 1.57 mm / Ø 0.060 – 0.062 in | 90 g / 0.20 lb | 182 g /0.40 lb |
| GSF16D-B for wire Ø 1.60 – 1.63 mm / Ø 0.063 – 0.065 in | 90 g / 0.20 lb | 182 g /0.40 lb |
| GSF18D-B for wire Ø 1.80 mm / Ø 0.073 in | ||
– Guide Tube Length: 126 cm / 49.6 in
– Package Dimensions (L x W x H) 245 x 185 x 45 mm 9.65 x 7.28 x 1.77 in
Complies with CE standards. ESD safe
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here:
https://www.jbctools.com/productregistration/within30daysofpurchase.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility
