Contents
hyco Ara Instantaneous Inline Water Heater
Usage
Effective low cost solution for light hand washing at a single basin. Compact design, energy efficient and easy to install. Buy with our compatible hot and cold tap as a set for convenience and confidence. Confirm that the flow rate and temperature performance is adequate for your application using the chart and tables provided.
Features and Benefits
- Supplies hot water to a single outlet for light hand washing only
- Bare wire heating system gives fast heat up time
- Heats the water instantly as it flows through the unit
- Energy efficient –no standing losses
- 3.0 kW power rating
- Easy to install, 13 amps connects to standard wiring
- Ideal bought as a set with our hot and cold tap or for IN30T use with a Vega infrared tap (page 60)
- Not suitable for use with thermostatic mixing valves or taps or to supply a single lever mixer tap
- Must be used with a spray head tap
- Supplied 1.6l/m flow restrictor must be fitted to the tap spout giving giving a temperature uplift of 27°C
- This will give 42°C in summer, incoming water temp 15°C and 37°C in winter, incoming water temp 10°C.
Thermostatic Model Only
- External electronic thermostatic control accurate to the nearest degree
- LED temperature display
- Energy saving – only uses the power required to deliver the chosen temperature
- Heating power automatically adjusted to compensate for temperature, flow rate and water pressure variations
- Temperature factory set at 38°C and can be adjusted by the user between 35°C and 50°C. In normal usage the maximum temperature is 37°C to 42°C.
- After power interruption the unit will recall the last usage outlet temperature but must be turned back on using the touch screen.
| Product Code | Includes
HCTAP1 |
Power
(kW) |
Thermostatic | Max Flow Rate
(l/m) handwash* |
Standing Loss
(kWh/day) |
| IN30SET IN30 | Yes
No |
3.0 | No | 1.7 | 0 |
| IN30TSET IN30T | Yes
No |
3.0 | Yes | 1.7 | 0 |
Outer Casing
Easy clean high impact ABS
Heating Element
Bare-wire heating system
Controls (Thermostatic Model only)
Temperature display (°C)
Power on/ off button
+/- controls allow the user to set the required temperature.
Tap and Tap Spray Nozzles
See features and benefits section
Safety
Overheat temperature protection IN30 – 75°C, IN30T – 85°C. Thermostatic model – water temperature controlled to maintain user selected temperature between 35°C and 50°C as water pressure conditions vary.
IP Rating
IP24 – IN30
IP24 – IN30T
Installation
This appliance must be installed in a frost free environment.
The heater should be located as close as practical to the hot water outlet to avoid unnecessary heat losses through the pipework.
Plumbing
Must be installed by a suitably qualified person.
Minimum flow rate 1.2 l/m.
Minimum water pressure 0.5 bar.
Maximum water pressure 8.0 bar.
Water resistivity ≥ 1300 Ωcm.
Water Connection
Inlet/ Outlet 2 x 1/2” BSP male
(37mm apart centre to centre). Fittings required (not supplied):
2 x 15mm compression to 1/2” BSP female adapter.
Thermostatic model only is suitable for use with pre-heated water e.g. solar heating systems subject to maximum inlet water temperature 60°C.
Electrical Connection
Installation must comply
with current IET wiring regulations.
Single phase. Fuse rating guide 13 amps.
The product should be connected to the fixed wiring of the property via a suitably rated isolating switch with a contact separation of at least 3mm in all poles.
Cable pre-wired 0.7m.
Approvals
CE, UKCA
Standard Warranty
1 year parts or replacement warranty.
| Product Code | Height
(mm) |
Width
(mm) |
Depth
(mm) |
Weight (kg)
Empty |
| IN30 | 170 | 135 | 70 | 0.9 |
| IN30T | 130 | 185 | 90 | 1.3 |
| HCTAP1 | 230 | 170 |