INSTRUCTION SHEET
Contents
CFS303 CADDY Slick Nut
CADDY® SLICK NUT
To install
To install With threaded rod
See Recomended Torque in table on sheet 2
To remove:
FEATURES
- Easy to mount — one hand installation.
- No springs or washers required.
- Allows threaded rod to be installed after positioning of the CADDY SLICK NUT.
- One size fits all strut depths.
WARNING:
- ERICO products shall be installed and used only as indicated in ERICO product instruction sheels and training materials. Instruction sheets are availoble at www.erico.com ond from your ERICO customer service representative.
- ERICO products must never be used for o purpose other than the purpose for which they were designed or in o manner that exceeds specified load ratings.
- Al instructions must be completely followed to ensure proper and sfe installation ond performonce.
- Improper installotion, misuse, misapplication or other failure to completely follow ERICO’s instructions and warnings moy cause product malfunction, property damoge, serious bodily injury and death.
- Products that are manufactured using spring steel components shall be used only in o non—corrosive indoor environment.
- Al pipe supports, hongers, intermediate components and structural attachments must ONLY be used os described herein and are NEVER to be used for ony other purpose.
NOTE: Al load ratings are for static conditions and do not account for dynamic loading such as wind, woter or seismic loads, unless otherwise noted.
The customer is responsible o. Conformance o all gover b. The integrity of structures to which the products are attached, including their capabilty of safely accepting the loads imposed, as evaluated by o qualiied engineer. c. Using appropriate industry stondord hardware s noted above.
SAFETY INSTRUCTIONS: All governing codes and requlations and those required by the job site must be observed. Aways use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the opplication.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH and LENTON ore registered trademarks of ERICO International Corporation.
| Part Number | Article Number | Thread Size | A Torque |
Recommended | Fl | |||
| in | mm | ft—lb | N—m | lbs | N | |||
| SLICK250 | Not Applicable |
1/4″ | Not Applicable |
4 | 6 | 400 | 1800 | |
| SLICK375 | 3/8″ | 10 | 14 | 600 | 2700 | |||
| SLICK500 | 1/2″ | 10 | 14 | 600 | 2700 | |||
| SLICKM6 | 174460 | M6 | 4 | 6 | 400 | 1800 | ||
| SLICKM8 | 174340 | M8 | 6 | 8 | 600 | 2700 | ||
| SLICKM10 | 174350 | M10 | 10 | 14 | 600 | 2700 | ||
| SLICKM12 | 174550 | M12 | 10 | 14 | 600 | 2700 | ||
| SLICKM8050 | 174360 | M8 | 1.30 | 33.0 | 6 | 8 | 600 | 2700 |
| SLICKM8070 | 174370 | M8 | 2. | 53.0 | 6 | 8 | 600 | 2700 |
| SLICKM8090 | 174380 | M8 | 3. | 73.0 | 6 | 8 | 600 | 2700 |
| SLICKM10050 | 174410 | M10 | 1.30 | 33.0 | 10 | 14 | 600 | 2700 |
| SLICKM10070 | 174420 | M10 | 2. | 53.0 | 10 | 14 | 600 | 2700 |
| SLICKM10090 | 174430 | M10 | 3. | 73.0 | 10 | 14 | 600 | 2700 |
Static Loads:
(Applicable for 14ga[2.0mm] and 12ga[2.5mm] strut)
TECHNICAL SUPPORT: www.erico.com
CFS303_E
©2000,2004,2014
ERICO International Corporation