Contents
Danfoss BFP-11L3 Diamond Oil Pump
Installation Guide
- 1-pipe operation: screw with washer
- 2-pipe operation: screw without a washer
- 1-pipe operation: without screw
- 2-pipe operation: screw fitted
Installation Guide, BFP
Fuel gas oil 6 mm2/s
| H
m |
Ø4 mm | Ø5 mm | Ø 6 mm | Ø 4 mm | Ø 5 mm | Ø 6 mm | Ø 5 mm | Ø 6 mm | Ø 8 mm |
| 4,0
3,5 3,0 2,5 2,0 1,5 1,0 0,5 |
51
45 38 32 26 19 13 6 |
100
100 94 78 62 47 31 16 |
100
100 100 100 100 97 65 32 |
26
22 19 16 13 10 6 3 |
62
55 47 39 31 23 16 8 |
100
100 97 81 65 49 32 1 |
31
27 23 20 16 12 8 4 |
65
57 49 40 32 24 16 8 |
100
100 100 100 100 77 51 26 |
| GB Nozzle capacity | 2,5 kg/h | 5 kg/h | 10 kg/h | ||||||
Fuel gas oil 6 mm2/s (cSt)
| H
m |
Ø4 mm | Ø 5 mm | Ø 6 mm | Ø 4 mm | Ø 5 mm | Ø 6 mm | Ø 5 mm | Ø 6 mm | Ø 8 mm |
| 4,0
3,5 3,0 2,5 2,0 1,5 1,0 0,5 |
100
95 89 83 77 71 64 58 |
100
100 100 100 100 100 100 100 |
100
100 100 100 100 100 100 100 |
51
48 45 41 38 35 32 29 |
100
100 100 100 94 86 79 71 |
100
100 100 100 100 100 100 100 |
62
58 54 51 47 43 39 35 |
100
100 100 100 97 89 81 73 |
100
100 100 100 100 100 100 100 |
| Nozzle capacity | 2,5 kg/h | 5 kg/h | 10 kg/h | ||||||
Fuel gas oil 6 mm2/s
| H
m |
Ø4 mm | Ø 5 mm | Ø 6 mm | Ø 4 mm | Ø 5 mm | Ø 6 mm | Ø 5 mm | Ø 6 mm | Ø 8 mm |
| –0
–0,5 –1,0 –1,5 –2,0 |
52
46 40 33 27 |
100
100 97 81 66 |
100
100 100 100 100 |
26
23 20 17 14 |
63
56 48 41 33 |
100
100 100 84 69 |
32
28 24 20 17 |
66
58 50 42 34 |
100
100 100 100 100 |
| Nozzle capacity
|
2,5 kg/h | 5 kg/h | 10 kg/h | ||||||
Fuel gas oil 6 mm2/s
| H
m |
2800 min–1 | |||||
| BFP 3 | BFP 5 | |||||
| Ø 6 mm | Ø 8 mm | Ø 10 mm | Ø 6 mm | Ø 8 mm | Ø 10 mm | |
| 4,0 | 33 | 100 | 100 | 21 | 67 | 100 |
| 3,5 | 31 | 98 | 100 | 20 | 63 | 100 |
| 3,0 | 29 | 91 | 100 | 19 | 59 | 100 |
| 2,5 | 27 | 85 | 100 | 17 | 55 | 100 |
| 2,0 | 25 | 79 | 100 | 16 | 51 | 100 |
| 1,5 | 23 | 72 | 100 | 15 | 46 | 100 |
| 1,0 | 21 | 66 | 100 | 13 | 42 | 100 |
| 0,5 | 19 | 60 | 100 | 12 | 38 | 94 |
| 0 | 17 | 53 | 100 | 11 | 34 | 84 |
| –0,5 | 15 | 47 | 100 | 10 | 30 | 74 |
| –1,0 | 13 | 41 | 99 | 8 | 26 | 64 |
| –1,5 | 11 | 34 | 84 | 7 | 22 | 54 |
| –2,0 | 9 | 28 | 68 | 6 | 18 | 44 |
| –2,5 | 7 | 22 | 53 | 4 | 14 | 34 |
| –3,0 | 5 | 15 | 37 | 3 | 10 | 24 |
| –3,5 | 3 | 9 | 22 | 2 | 6 | 14 |
| –4,0 | 1 | 3 | 6 | 1 | 2 | 4 |
Oil pump type BFP
Technical data
| Oil types | Standard fuel gas oil and fuel gas oil acc. to DIN V 51603-6 EL A Bio 10 |
| Viscosity range | (1,3) 1,8-12 mm2/s (cSt) |
|
Speed |
type 5 1400-3450 min-1
type 3 2400-3450 min-1 |
| Pressure range1: BFP 11
BFP 20, 21 and 41 Factory setting |
7-15 bar 7-20 bar 10 bar |
| Coil voltage Coil enclosure | 220/240 V, 50/60 Hz)
IP 40 |
| Temperature of medium | 0 to 70° C |
- Max. 12 bar to 1.3 cSt., max. 15 bar to 1,8 cSt.
Connections (figs. 1, 2, 3 and 4)
Bleeding
Bleeding the oil pump is only necessary with 1-pipe systems. On 2-pipe systems the pump is automatically bled through the return pipe.
Filter cleaning/filter replacement with ring filter (fig. 5)
Remove the four screws with a 4 mm hexagon key. Take off the cover. The filter can then be taken out for cleaning or replacement.
Filter replacement with cartridge filter (fig. 6)
Unscrew the filter plug in the cover with a 4 mm key and pull out the cartridge filter. If necessary, insert a screwdriver between filter and plug and carefully twist the filter out.
Scrap the filter and fit a new one onto the plug! Reassemble the cartridge filter and tighten it.
Changeover between 1-pipe and 2-pipe operation (figs 7 and 8)
Suction line lengths in meters
The tables apply to a standard fuel gas oil (Heizöl-EL) of normal commercial quality to current standards. When starting a system with empty piping, the oil pump should not be allowed to operate without oil for more than 5 minutes.
Attention!
BFP 20 pumps are without a solenoid valve. The oil pumps are used only for oil burners.
Please note that the solenoid valve must be replaced after 250.000 operations or 10 years (approved life expectancy)
Any information, including, but not limited to information on the selection of the product, its application or use, product design, weight, dimensions, capacity or any other technical data in product manuals, catalog descriptions, advertisements, etc., and whether made available in writing, orally, electronically, online or via download, shall be considered informative and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility for possible errors in catalogs, brochures, videos, and other material. Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to the form, fit, or function of the product. All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved.
Specifications
- Product Name: Oliepumpe type BFP
- Model Numbers: BFP 11 L3, BFP 11 R3, BFP 20/21, BFP 41
- Pressure Regulation: Ps = 0 kPa to Ps = 35 kPa
- Connection Sizes: G 1/4, G 1/8
- Filter Type: Cartridge filter
FAQ
Q: What should I do if I notice a leak in one of the connections?
A: If you notice a leak, immediately turn off the system and address the leak by tightening the connection or replacing any damaged components. Restart the system only after ensuring that the leak has been resolved.
Q: How often should I clean or replace the cartridge filter?
A: The cartridge filter should be cleaned or replaced according to the manufacturer’s recommendations or if you notice a decrease in system performance.