51 147.6
Technical amendments reserved
Wall luminaire for indoor use
Instructions for use
Contents
51147.6 Wall Luminaire for Indoor Use
Application
Wall luminaire · indoor luminaire with velvet white luminaire housing and inside hue.
The light emits upwards and downwards.
Luminaire slope angle: 18°.
Product description
Wall luminaire “STUDIO LINE”
Satin white finish.
Aluminium housing shield,
Finish Colour velvet white inside hue matt copper
Light-diffusing synthetic disks with optical texture
2 elongated fixing holes
Width 4.5 mm · 26 x 28 mm spacing
1 cable entry for mains supply cable
Connecting terminals 2.5@
Earth conductor terminal
LED power supply unit
220-240 V 
0/50-60 Hz
DC 176-275 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
– Conformity mark
Weight: 1.6 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 17.1 W |
| Luminaire connected wattage | 19.5 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 30 °C |
51 147.6 K3
| Module designation | |
| LED-1224/930 + LED-1225/930 | |
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 2820 lm |
| Luminaire luminous flux | 1315 lm |
| Luminaire luminous efficiency | 67,4 lm / W |
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the hexagon socket head screw (wrench size 2.5 mm) and lift luminaire.
Unplug the earth conductor connection (plug contact).
Pass the power connecting cable through the cable entry in the mounting plate.
Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
Note position of application of the mounting plate “arrow down”.
Establish the earth conductor connection on the earthing screw (1) of the mounting plate.
Push silicone sleeves over the lines.
Make the electrical connection to the terminals.
Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
The two connecting terminals marked DA, DA are provided for digital control purposes.
If these terminals are not assigned, the luminaire will work with full light output.
Make earth conductor connection between luminaire housing and mounting plate (plug contact).
Place connecting terminals inside the luminaire wall bracket.
Install luminaire over mounting plate and tighten hexagon socket head screw (wrench size 2.5 mm) evenly.
Guide the housing shield provided over the luminaire’s light-diffusing synthetic lenses and into its end position.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Defective luminaire cover must be replaced.
Close the luminaire.
Spares
| LED power supply unit | DEV-0402/520i |
| LED module 3000 K unten | LED-1224/930 |
| LED module 3000 K oben | LED-1225/930 |
| Housing shield | 71 003 492 B6 |
Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
[email protected]
www.bega.com