BEGA 50264.1 LED Wall Luminaire for Indoor Use Instruction Manual

BEGA 50264.1 LED Wall Luminaire for Indoor Use

Product Information

Product Description	Metal housing, finish colour white
Hand-blown Opal Glass	Satin matt
Cable Entry	1 entry for through-wiring
Connecting Terminals	2.5@
LED-Module Voltage	Mains voltage 220-230 V, 50/60 Hz
Weight	1.2 kg
Energy Efficiency Class	F

Product Usage Instructions

1. Installation:
   • LED components are high-quality electronic components. Avoid touching the light output opening of the LED directly during installation or relamping.
   • Lead the main supply cable through the cable entry of the luminaire base.
   • Fix the luminaire base with the enclosed or any other suitable fixing material onto the mounting surface. Use the gasket rings supplied.
   • Establish an earth conductor connection and make the electrical connection to the terminals.
   • Take into account that glass and metal have different expansion rates. Place the glass into the luminaire base and fix the set screws hand-tight. After tightening, loosen the set screws for half a turn to allow the glass to move.
2. Replacing the LED Module:

The designation of the LED module is noted on

Application

• Shielded wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt with a metal shield, for many lighting tasks.
• The light emits upwards and downwards.

Product Description

• Metal housing, finish colour white
• Hand-blown opal glass, satin matt
• Metal shield, white 2 elongated fixing holes
• Width 4.5 mm · 185 mm spacing 1 cable entry for through-wiring for mains cable
• Connecting terminals 2.5@
• Earth conductor connection
• LED-Module for mains voltage 220-230 V y 50/60 Hz
• BEGA Thermal Switch®
• Temporary thermal shutdown to protect temperature-sensitive components
• Safety class I
  • Safety mark
  • Conformity mark
• Weight: 1.2 kg
• This product contains light sources of energy efficiency class(es) F

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Lamp Specification

• Luminaire connected wattage 10 W
• Rated temperature ta = 25 °C
• Ambient temperature ta max = 35 °C

50 264.1 K3

• Module designation LED-0607/930
• Colour temperature 3000 K
• Colour rendering index Ra > 90
• Module luminous flux 940 lm
• Luminaire luminous flux 495 lm
• Luminaire luminous efficiency 49,5 lm / W

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• Lead the main supply cable through the cable entry of the luminaire base.
• Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
• Be sure to use the gasket rings supplied.
• Establish an earth conductor connection and make the electrical connection to the terminals.

Advice:

• The expansion of glass and metal is different.
• The glass must be allowed to expand.
• Place glass into the luminaire base and fix the set screws hand-tight.
• After tightening the set screws loosen them for half a turn to allow the glass to move.

Dimension

Cleaning And Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified electrician or a comparably qualified person using standard tools.
• Disconnect the electrical installation.
• Open the luminaire.
• Please follow the installation instructions for the LED module.
• Close the luminaire.

Spares

• Spare glass 11 003 223 .0M RG
• LED module 3000 K LED-0607/930

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · [email protected] · www.bega.com.