Wall luminaire
24 023
Contents
24023 Wall Luminaire
Instructions for use
Application
Shielded wall luminaire made of aluminium alloy and hand-blown three-ply opal glass.
A luminaire with uniform light distribution for a variety of lighting tasks in interior and exterior lighting applications.
Product description
Luminaire made of aluminium alloy and stainless steel BEGA Unidure® coating technology Opal glass with sliding bolt glass closure 2 mounting holes ø 4.8 mm Distance apart 100 mm 1 cable entry for mains supply cable up to ø 10,5 mm Connection terminal 2.5@ Earth conductor connection LED-Module for mains voltage 220-230 V 
50/60 Hz BEGA Thermal Switch® Temporary thermal shutdown to protect temperature-sensitive components Safety class I Protection class IP 44 Protected against granular foreign bodies ≥ 1 mm and splash water Impact strength IK06 Protection against mechanical impacts < 1 joule 
– Safety mark 
– Conformity mark
Weight: 1.7 kg
This product contains light sources of energy efficiency classes F
| Lamp | |
| Luminaire connected wattage | 7.4 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 45 °C |
| 24 023 K3 | |
| Module designation | LED-0662/830 |
| Colour temperature | 3000 K |
| Colour rendering index | Ra > 80 |
| Module luminous flux | 760 lm |
| Luminaire luminous flux | 279 lm |
| Luminaire luminous efficiency | 37,7 lm / W |
Safety
The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Installation
Lead the mains supply cable through the cable entry of the luminaire base.
Notice position of use “arrow down” of the luminaire back plate.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
In order to guarantee the maximum service life of the electrical components, the enclosed esiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Insert the opal glass into sliding bolt glass closure and turn the glass clockwise up to the stop.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
| Spares | |
| Spare glass with graphite cap | 11 002 375 S1 |
| Spare glass with white cap | 11 002 375 W1 |
| LED module 3000 K | LED-0662/830 |
| LED module 4000 K | LED-0662/840 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
[email protected]
www.bega.com