REMORA 7320
ROBOT POOL CLEANER
INSTRUCTION MANUAL
Contents
7320 Remora Robot Pool Cleaner
Congratulations on the purchase of your new Remora Robotic Pool Cleaner.
This is a powerful autonomous cleaner arrives to you ready to plug in and play. Great for pools of any shape.
This cleaner comes with a floating swivel that ensures you have minimum cord tangling issues and a large easy to access debris basket.
Please check the packaging to insure all parts are ready for install. If any parts are missing or damaged, please contact us.
Product Specifications
Maximum Depth: 2.5m / 8ft
Maximum Pool Size: 10m x 5m / 33ft x 17 ft
Power supply input: 100-130V AC / 200
230V AC
Power supply output:
<24VDC
!!Warnings!!
2.1 Please review your local pool safety regulations
2.2 Keep power supply away from pool edge by at least 3.5 m / 11ft
2.3 Ensure your electrical outlets are properly grounded
2.4 Have a Ground Fault Current Interrupter (GFI) and/or an Earth Leak Interrupter (ELI)
2.5 Keep power supply out of water
2.6 Do not run the robotic cleaner out of water
2.7 Make sure power supply is unplugged before any maintenance
2.8 Do not operate with a damaged cord or power supply
2.9 Do not operate with people swimming in the pool
2.10 For use in water with temperatures between 5-36°C / 41-97°F
Included Content
- Robotic Pool Cleaner
- Power supply
- Floating cord with swivel
- Side brushes
Getting Started
*Your cleaner comes to you fully assembled in the package. *
- Place your power supply about approximately at the middle point between both ends of your pool and a few meters/feet away from the edge of the pool. (Fig 4.1)
- Put the pool cleaner into your pool and wait until it has fully submerged. If needed, manually submerge the cleaner. (Fig 4.2)
- For optimum performance, place the vacuum at a spot in the pool farthest from the power supply.
This is the proper length of cord needed for the robot to reach the entirety of your pool. Remove any extra grey floating cord from the pool and secure near the power supply with the provided reusable cable fasteners. NOTE: Leaving extra cord in the pool will increase chance of cord tangling - Plug in the power supply to a nearby electrical outlet. A blue status light should turn on.
- Unscrew the cap next to the switch (Fig 4.3). Insert the end of the floating cord into the outlet revealed (Fig 4.4). Take note of the orientation of the plug and outlet.
- Screw tightly in the nut from the floating cord. Flip the switch in the middle to the side with the blue light (Fig 4.5). This will turn on the power supply.
- Press the power button at the top of the power supply to turn on your robotic cleaner (Fig 4.6). Note that a red indicator light should turn on (Fig 4.7).
- To turn off your cleaner, press and hold down the power button for 3 second. Alternatively, you can flip the switch to the opposite direction turning off the power supply.
- When cleaner will no longer be used or will be stored for extended period of time, replace the cap attached to the power supply.
*If the red or blue indicators lights are flashing, please refer to Troubleshooting section.
Cleaning the filter basket
- Open the cover on the top of the cleaner to access the filter basket (Fig 5.1).
- Use both hands to lift up the basket using the handles at the side of the basket (Fig 5.2).
- Flip open the baskets lid by pulling the tab at the front of the basket (Fig 5.3) and dump the contents inside.
- Dump out the debris inside the basket. Use a hose to spray water and clean the filter screens. While the filter basket is removed from the vacuum, spray the inside of the cleaner with water to remove any small debris that may have accumulated inside the cleaner.
Then hose the entire unit off with fresh water including the cord and swivel. - When cleaned, place your basket back into your robotic cleaner. If basket is not properly aligned, it will not lock into place.
- Press down on the handles to lock in your basket (Fig 5.4).
Troubleshooting
| Symptom | Possible reason(s) | Solution(s) |
| Pump is running but robot is not moving | No/not enough power is going to robot An object is blocking robot’s rollers, tracks, impeller |
Unplug power supply and take robot out of water. Open basket cover and remove basket. Check that there no foreign object in the impeller. Check that there is no foreign object blocking the track or rollers |
| Pump and drive roller are not operating |
Robot is not connected to power supply Power supply turned off |
Check that the power supply is on Check all connections from robot to power supply |
| Robot does not pick up debris when running over it . Robot is not climbing. |
Clogged/full basket An object is stuck in impeller or grill |
Clean the basket and filter screens. Clean fine filter pad if used Check if basket is inserted properly. (refer to chapter Cleaning the Filter Basket) Check that there is no foreign object in the impeller or lodged in the grill above the impeller |
| Not cleaning all areas of the pool. | Not enough/ too much floating cord in the pool | Insure that there is just enough floating cord in the pool for the cleaner to reach all areas of the pool. Remove from the pool all extra cord and secure near power supply with included reusable cord fasteners. |
| Item | Part number | Part description |
| 1 | 71000 | Top shell. Dark grey |
| 2 | 71010 | Debris basket assembly (parts 16 and 17 included) |
| 3 | 71020 | Top lid. Smoke |
| 4 | 71040 | Impeller |
| 5 | 71050 | Pump motor block |
| 6 | 71070 | Pump cover lid. Black |
| 7 | 71080 | Handle. Black |
| 8 | 71090 | Geared roller tube assembly. Black |
| 9 | 71100 | Bottom chassis. Dark grey |
| 10 | 71110 | Fast drain flap. Dark grey |
| 11 | 71120 | Side support assembly. L. Black |
| 12 | 71130 | Drive belt track. Black |
| 13 | 71140 | Geared wheel. 4pcs as a set. Grey |
| 14 | 71150 | Front roller assembly. Grey and black |
| 15 | 71160 | Side support assembly. R. Black |
| 16 | 71012 | Non return inlet assembly |
| 17 | 71011 | Tcp filter screen |
| 18 | 33110 | Machine end Sooting cord. 3m long. Grey |
| 19 | 33290 | Floating cad with swivel. 13m long. Grey |
| 20 | 36000 | Power cad. UK standard |
| 21 | 36001 | Power cord. Australia standard |
| 22 | 36002 | Power cord. US standard |
| 23 | 36003 | Power cad. VDE Europe standard |
| 24 | 36004 | Power cad. China standard |
| 25 | 30180 | PaAer supply |
| 26 | 71180 | PVC brush set 5pcs as a set |
| 27 | 71170 | Fne filtration pad. Seigle side |
