The Dispensing Specialist
LEVER ACTION PUMP
User Manual
Contents
Lever Action Pump
Food Pan Pumps
 |
Part# | |
| 300136 | Lever Action Pump, 10mm, 1/6 pan | |
| 300134 | Lever Action Pump, 10mm, 1/4 pan | |
| 300133 | Lever Action Pump, 10mm, 1/3 pan | |
Bain Marie Pumps
 |
Part# | |
| 300135 | Lever Action Pump, 10mm, #10 Can | |
| 300104 | Lever Action Pump, 10mm, 4 Qt | |
| 300107 | Lever Action Pump, 10mm, 7 Qt | |
| 300111 | Lever Action Pump, 10mm, 11 Qt | |
Fountain Jar Pumps
 |
Part# | |
| 300130 | Lever Action Pump, 10mm, 7″ & 10″ Fountain Jar | |
Parts
Safety
All components must be cleaned before first use.
According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines. Be aware of the product you are serving and the temperature the product is required to maintain.
IMPORTANT: Clean, rinse, sanitize, and dry parts at a minimum of every 24 hours. Always comply with local sanitization requirements.
Cleaning
Disassemble all parts. Clean with soap, hot water, and brush.
Wash, rinse, sanitize, and dry parts according to local sanitization requirements.
Assembly
Insert the piston.
Secure the piston by tightening the thumb screw in the upper piston assembly. 
Screw the lower valve assembly into the pump body.
Screw the discharge tube assembly to the pump body.
Make sure valve is in place in the discharge tube.
Attach pump body to lid assembly.
Twist lid lock clockwise to lock Lid.
Disassembly
Twist lid lock counter-clockwise to unlock Lid.
Pull down to separate pump body from lid assembly.
Unscrew the discharge tube assembly from the pump body.
Unscrew the lower valve assembly from the pump body.
Loosen the thumb screw in the upper piston assembly. Pull the piston through the lid.
Tips & Troubleshooting
Pump feels loose:
Make sure lid lock is properly engaged.
Pump is not dispensing product:
Make sure valve is in place in the discharge tube.
Setting the Portion
BEFORE FULL ASSEMBLY Remove collar nut.
Slide collar up, lift handle clear of upper piston assembly.
Remove upper piston assembly.
Watch Spring!
Slide portion ring over spring housing. Reassemble.
NOTE: Each ring reduces portion by ¼ fl oz.
ASEPT General Warranty
Liability for defects
Should the products, as delivered, within one (1) year from delivery be shown to be defective due to defaults in material or manufacturing (“Warranty Period”), the Supplier undertakes, at its own option (i) to make a replacement delivery, (ii) to repair or rework the products claimed to be defective or (iii) to accept return of such product and refund such proportion of the purchase sum received as corresponds to the returned products. The Supplier assumes no liability for defects as regards to layout and design of the products, unless expressly stated in the Agreement.
The Customer shall without undue delay notify the Supplier in writing of any defect which appears. Such notice shall under no circumstances be given later than two (2) weeks after the expiry of the Warranty Period.
The Supplier is liable only for defect which appear under the conditions of operation provided for in the Agreement and under proper use of the product. The Supplier’s liability does not cover defect which are caused by faulty maintenance, incorrect use or faulty repair by the Customer, or by alterations carried out without the Supplier’s consent in writing. Finally, the Supplier’s liability does not cover normal wear and tear or deterioration.
Except as expressly specified above, the Supplier has no liability for defects in the products whatsoever and are under no circumstances responsible for any direct or indirect losses, damages or costs incurred by the Customer, including consequential damages.
General limitation of liability
Notwithstanding any other limitation of liability mentioned in the Agreement including these Terms and Conditions, the Supplier’s liability for damages under the Agreement shall be limited to the insurance compensation that
can be obtained in accordance with the Supplier’s each valid liability insurance.
Consequential losses
There shall be no liability of either party towards the other party for loss of production, loss of profit, loss of use, loss of contract or for any other consequential or indirect loss whatsoever.
ASEPT International Inc.
5207 N. 125th St.
Butler, WI 53007, USA
888-927-3785
[email protected]
ASEPT International AB
Traktorvägen 17, SE-226 60
Lund, Sweden
+46 46 329 700
[email protected]
www.asept.com
330032 10/23