Schlage Control Smart Deadbolt FE410F Installation Manual

Home » Schlage » Schlage Control Smart Deadbolt FE410F Installation Manual

Schlage Control™ Smart Deadbolt    SCHILAGE

with Engage Technology

Model FE410F

Door Preparation Instructions for Door with No Holes

Tools Needed

Tape Measure

Pencil
Pencil

Pencil

Drill Bits Neede
Drill Bits Needed

Drill and Drill Bits

Bit Sizes: ¹⁄₈”,  1”

Drill Bits Neede 1
Hole Saw

Hole Saws

1″ 2¹⁄₈”

Chisel
Chisel

Chisel

Hammer
Hammer

Hammer

1 Measure door thickness.

If the door is thinner than 1³⁄₈,” or thicker than 1³⁄₄”, then the lock will not fit properly on the door.

Measure door thickness

i A thick door kit is available from Product Support at 800-847-1864.

2 Mark lock centerlines.

2a Mark bottom centerline on door face, door edge and door jamb.

Mark lock centerlines
Door Edge, Door Jamb, Door Face, 38” from finished floor, Tape

2b Mark top centerline on door face, door edge and door jamb.

Mark top centerline on door face, door edge and door jamb
Door Edge, Door Jamb, Door Face, 4” or 5Zx” from bottom centerline

i Locks are ordered as either 4” or 5½”.

3 Prepare cross bores.

3a Measure backset and mark center of holes.

Measure backset and mark center of holes

3b Drill holes with hole saw.

Drill holes with hole saw
Hole Saw
4 Prepare door edge holes.

4a Measure and mark ½ door thickness.

Measure and mark 1 2 door thickness
Door Thickness

4b Drill holes in door edge.

Drill holes in door edge
Drill Bit or Hole Saw
5 Mortise for latch and bolt.

5a Insert latch into door edge hole. Trace latch faceplate and mark holes.

Mortise for latch and bolt

5b Remove latch and bolt. Drill four ¹⁄₈” pilot holes.

Remove latch and bolt. Drill four
Drill Bit

5c Use chisel and hammer to create mortise for latch and bolt.

Use chisel and hammer to create mortise for latch and bolt

6 Measure, mark and drill holes in door jamb for strikes.

6a Mark center for strike holes exactly opposite latch and bolt holes.

Mark center for strike holes exactly opposite latch and bolt holes

6b For the bolt strike, measure, mark and drill two (2) 1” holes, 1¼” deep, as shown. Chisel out excess material on the sides.

For the bolt strike, measure, mark and drill
Drill Bit or Hole Saw

6c For the latch strike, measure, mark and drill two (2) 1” holes, ½” deep, as shown. Chisel out excess material on the sides.

For the latch strike, measure, mark and drill
Drill Bit or Hole Saw
7 Mortise for latch and bolt strike.

7a Trace latch strike and bolt reinforcement plate. Mark holes.

Trace latch strike and bolt reinforcement plate

7b Drill six (6) ¹⁄₈” pilot holes.

Drill six (6) pilot holes
Drill Bit

7c Use chisel and hammer to create mortise for strikes and reinforcement plate.

Use chisel and hammer to create mortise for strikes and reinforcement plate

i Mortise for latch strike extends all the way to the edge of the jab to allow for the latch lip.

Product Support

800-847-1864      www.allegion.com

Allegion Logo © Allegion 2016 FE410F door prep no holes-b Rev. 05/16-a

Schlage Control Smart Deadbolt FE410F Installation Manual –
Schlage Control Smart Deadbolt FE410F Installation Manual –

Leave a Comment