axial AXI03008T1 SCX10 III Jeep CJ-7 Instruction Manual

axialadventure.com
1/10TH SCALE READY-TO-RUN 
SCX10™ III JEEP® CJ-7

AXI03008T1 SCX10 III Jeep CJ-7

INSTRUCTION MANUAL
Scan the QR code and select the Manuals and Support quick links from the
product page for the most up-to-date manual information.
AXI03008T1/T2
https://horizonhobby.cc/3qXewyB?r=qr

NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
SAFETY PRECAUTIONS AND WARNINGS
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.

• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as the motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.
• Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of the radio equipment.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM® or Spektrum technology.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine.
The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.
GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Caution should be taken when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your transmitter’s manual or the manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.
• Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed.
  CAUTION: Always keep hands, fingers, tools and any loose or hanging objects away from rotating parts when performing the above drying technique.
• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.
  NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil. Do not spray the motor.
• Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the following:
  – Front and rear axle hub assembly bearings.
  – All transmission cases, gears and differentials.
  – Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.

BOX CONTENTS

• Spektrum™ DX3™ 2.4GHz Transmitter (SPM2340)
• Axial® SCX10™ III Jeep® CJ-7 RTR
  – 35T Electric Motor (DYNS1216)
  – Spektrum Receiver/ESC Combo (SPMXSE1040RX)
  – Water Proof Metal Gear Surface Servo, 23T (SPMS614)
  – SX108 Micro Analog Metal Gear Surface Servo (For dig function) (SPMSSX108)

REQUIRED EQUIPMENT

• 2-3S Standard or “Shorty” LiPo Battery OR
• 5-9 Cell NiMH/NiCad battery(IC3® Connector Required)
• Battery charger compatible with the chosen vehicle battery type

RECOMMENDED TOOLS

GETTING STARTED CHECKLIST

• Read the manual
• Familiarize yourself with the vehicle and its components
• Check all screws, especially the driveshaft setscrews, for tightness from the factory
• Charge the vehicle battery
• Install 4 AA batteries in the transmitter
• Install the vehicle battery in the vehicle
• Power on the transmitter and then connect battery to ESC
• Check for proper function of the throttle and steering
• Range check the radio system
• Drive the vehicle, challenge yourself, and have FUN!
• Perform any necessary vehicle maintenance

VEHICLE PARTS

CHARGE THE VEHICLE BATTERY

Follow the manufacturer’s directions for your charger to properly charge the vehicle battery.
CAUTION: Only use chargers designed to charge the chosen battery type. Using an incorrect charger or incorrect charger settings could cause the battery to catch fire or explode.

INSTALL THE TRANSMITTER BATTERIES

This transmitter requires 4 AA batteries (included).

1. Remove the battery cover from the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.

CAUTION: NEVER remove the transmitter batteries while the model is powered on. Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

TRANSMITTER FUNCTIONS

A/B. Channel 3 Button (Dig Function)
C. Throttle/Brake
D. Steering Wheel
E. Steering Rate
Adjusts the end point of the steering
F. Brake Rate
Adjusts the braking end point.
F. Steering Trim
Adjusts the steering center point. Normally, the steering trim is adjusted until the vehicle tracks straight.
G. Throttle Trim
Adjusts the throttle neutral point
I. SMART Battery Level Indicator
J. Servo Reversing
To reverse the Throttle (TH) or Steering (ST) channel, switch the position of the correlating switch—“N” is for normal, “R” is for reverse.
K. Throttle Limit
Limits throttle output to 50/75/100%
Select 50% or 75% for less experienced drivers or when you are driving the vehicle in a small area.
L. Power LED

• Solid red lights: Indicates radio connectivity and adequate battery power
• Flashing red lights: Indicates the battery voltage is critically low. Replace batteries

M. Power Button
N. Bind Button

ADJUSTING THE VEHICLE BATTERY TRAY

The battery trays may be adjusted to fit a wide range of battery sizes.
The rear battery tray is shown in the illustration. The side battery tray is adjustable in the same manner.
To adjust the battery tray:

1. Loosen the four flathead screws shown in the illustration.
2. Slide the ends of the battery tray in or out to fit the desired battery.
3. Tighten the four flathead screws. Do not over-tighten the screws.

INSTALL THE VEHICLE BATTERY

The following steps show the installation of a standard size battery in the rear battery tray of the vehicle. If you wish to use a “shorty” style battery, it should be installed in the side battery tray location.

1. Power on the transmitter.
2. Remove the four body clips from the body.
3. Gently lift the body from the chassis to preserve the wires that run from the headlight and taillights to the ESC.
4. Place the battery in the battery tray. The battery tray length may be adjusted to fit the battery as described in the previous section.
5. Secure the battery to the tray with the hook and loop strap.
6. Connect the battery to the ESC.
7. Re-install the body and four body clips to the chassis.

NOTICE: Always disconnect the battery from the ESC before powering off the transmitter. Loss of vehicle control may result.

BINDING

Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter.
Failsafe: Hold the steering wheel and throttle trigger in the desired failsafe positions during binding

1. Press and hold the bind button.
2. Power ON the receiver. The orange LED will begin to flash.
3. Set the trims and control positions at the desired failsafe settings.
4. Power ON the DX3 transmitter.
5. When the transmitter’s orange LED remains lit, it is connected to SPMXSE1040RX receiver/ESC combo.

You must rebind when:

• Different failsafe positions are desired (e.g., when throttle or steering reversing has changed).
• Binding the receiver to a different transmitter.

RANGE-CHECKING THE RADIO SYSTEM

The radio system should be checked before operating the vehicle to ensure proper operation and adequate range.

1. Turn on the transmitter.
2. Connect the battery in the vehicle.
3. Have a friend hold the vehicle while keeping hands and loose clothing away from moving parts.
4. Walk away until you are at the maximum planned operating distance from the vehicle.
5. Turn the steering wheel side to side and operate the throttle, both forward and reverse, checking for any erratic behavior.
6. If any erratic behavior is exhibited, DO NOT operate the vehicle. Contact customer service for assistance.

USING THE DIG TRANSMISSION

The vehicle includes a “Dig” transmission which allows the rear axle to lock while still allowing the front wheels to spin. Use this feature in close quarters to turn the vehicle tighter than is possible with normal 4 wheel drive or to preload the suspension when needed.
To use the Dig function:

1. Press and hold the channel 3 B button on the transmitter. The Dig function engages, locking the rear axle. Hold the B button as long as you want the dig function to be engaged.
2. Advance the throttle and turn the steering wheel left or right to tightly pivot the vehicle around.
3. Release the channel 3 B button to disengage the Dig function.
   TIP: Reversing slightly may be required to disengage the Dig function.
   If necessary, refer to the DX3 manual to adjust the endpoints of the Dig function.

VEHICLE MAINTENANCE
Just like a full size car or truck, your RC vehicle must undergo periodic maintenance in order to ensure peak performance. Preventative maintenance will also help avoid needless breakages which could result in costly repairs. Below are some suggestions to properly maintain your vehicle.

Replace any noticeable bent or broken parts	Check for wear on the ball joints in the steering and suspension links (replace if necessary)	Check driveshaft set screws and apply thread locking compound if necessary	Inspect shock absorbers for smooth dampened operation	Check for any loose connections or frayed wiring
Check the wheel nuts for tightness	Ensure the wheel beads are still firmly bonded around the entire circumference of the rim	Keep the chassis free of dirt and debris	Check for loose screws on the chassis, especially the knuckle, C-hub and axle lockout screws	Check the driveline for smooth, bind free operation
If applicable, check the slipper clutch for proper operation	Check the receiver antenna for damage	Check the steering operation for any binding	Inspect the spur and pinion gears for damage	Replace the transmitter batteries when indicated by the transmitter, as described in the Transmitter Functions section

SPEKTRUM RECEIVER/ESC COMBO

OPERATION

1. Power on the transmitter.
2.  Power on the receiver.
3. The green LED on the receiver will be illuminated when it is connected to your transmitter.
4. Disconnect the battery from the ESC/Receiver after operation.

FAILSAFE
In the unlikely event that the radio link is lost during use, the 2-in-1 will drive the throttle channel to the neutral (throttle off) position. If the 2-in-1 is powered on prior to turning on the transmitter, it will enter failsafe mode, leaving throttle off. When the transmitter is turned on, normal control will resume.
LED INDICATORS
Upon powering ON the ESC, the red LED will blink and the motor will emit a series of beeps to indicate its status.
The number of tones indicates (1) the ESC is in operation (2) the battery mode detected and (3) the ESC is in a ready-to-use state.

FEATURE	RED LED STATUS	MOTOR SOUND
ESC Is In Operation	Rapid Blinking	4 Changing Tones
Ni-MH/Ni-CD Battery 2S Li-Po Battery 3S Li-Po Battery	1 Blink 2 Blinks 3  Blinks	1  Short Tone 2  Short Beeps 3  Short Beeps
ESC Ready, No Transmitter Signal	2 Short Blinks, Red Blink Repeating	2 Ascending Tones, Descending Tones Repeating

OPERATION	LED STATUS
Forward
Partial Throttle	Green Solid, Red Blinks
Full Throttle	Green and Red Solid
Reverse
Partial Throttle	Green Solid, Red Blinks
Full Throttle	Green and Red Solid
Brake
Partial	Green Solid, Red Blinks
Full	Green and Red Solid
Stop	Green Solid
Battery Low Voltage or No Signal	Red Blinks
Overheat	Green Blinks
Over Current Protection	Green and Red Triple Blinks

SPECIFICATIONS
Type	Waterproof DSMR ESC/Receiver 2-in-1 with SMART Telemetry
Dimensions (L × W × H)	54mm × 33.5mm × 20.5mm
Antenna Length	31mm
Channels	4 (No Throttle Servo Output)
Weight	68g
Band	2404 MHz – 2476 MHz
Servo Output Voltage	6V up to 3A, Shared with Auxillary Light Connectors
Telemetry Features	Battery Voltage, Current, ESC Temp, Battery Data (with SMART Battery)
Battery Input Connector	IC3® (EC3™ Compatible)
Voltage Range	2–3S Li-Po*/5–9S NiMH
Max Current	40A Continuous/ 180A Burst
Motor Connectors	3.5mm Bullet

* Default setting for low voltage cutoff is Li-Po. Optional Dynamite Program Card (DYNS3005) required to change the Battery Type Setting.

ESC AND TRANSMITTER CALIBRATION

The included transmitter and ESC/receiver combo automatically calibrate when powered on. Follow the procedure below to ensure accurate calibration between the transmitter and ESC/receiver.

1. Connect a fully charged battery to the ESC/receiver. Ensure the power switch is in the OFF position.
2. Power the transmitter ON. Ensure the throttle is not reversed, the throttle trim is neutral and the throttle travel range is at 100%.
3. With the throttle at neutral, power ON the ESC/receiver.
4. Leave the throttle trigger and trims at neutral for at least 3 seconds.The ESC/Receiver automatically calibrates the throttle range after 3 seconds.
5. The LED will blink and the motor will beep to indicate the battery mode selection.
6. One long LED blink and one long beep indicates the ESC is ready to run.

GEAR RATIOS

SPUR/PINION GEAR RATIO CHART – LCX TRANSMISSION
	12	13	14	15	16	17	18
Low Speed (standard)	58.1	49.2	45.6	42.6	39.4	37.6	35.5
High Speed (optional)	39.8	36.5	31.3	29.2	27.3	25.7	24.3

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSE	SOLUTION
The system will not connect	Your transmitter and receiver are too close together	Move transmitter 8 to 12 feet away from receiver
	You are near metal objects	Move to an area with less metal
	The receiver is bound to a different model memory	Make sure the correct model memory is active in your transmitter
	Your transmitter was placed into bind mode and is no longer bound to your receiver	Rebind your transmitter and receiver, and then re-calibrate
The receiver goes into failsafe a short distance away from the transmitter	Check for damage on the receiver antenna	Make sure your receiver antenna is protected and located as high as practical
		Replace the receiver or contact Horizon Product Support
The receiver stops responding during operation	Low receiver battery voltage. If the battery voltage is low, it may drop below 3.5V momentarily, causing the receiver to brown-out, then reconnect	Charge the receiver or vehicle battery. Spektrum receivers require at least 3.5V to operate
	Loose or damaged wires or connectors between battery and receiver	Check the wires and connection between the battery and receiver. Repair or replace wires and/or connectors
Vehicle does not move	Batteries are not installed properly in the transmitter	Ensure the transmitter batteries are properly installed
	Weak or no battery in the vehicle	Install a freshly charged vehicle battery
	Damaged motor	Replace the motor
	Frayed or broken wiring	Replace any damaged wiring
	ESC is shut down by heat protection circuit	Allow the ESC to cool down completely
Loss of vehicle control	Improper antenna placement	Ensure the transmitter antenna is not blocked and the receiver antenna is located properly
	Weak or no batteries in the transmitter or vehicle	Install a freshly charged vehicle battery and new transmitter batteries
	Neutral or trim position is incorrect	Adjust the steering trim
	Receiver and/or battery not connected properly	Check all receiver and battery connections
Steering and/or throttle function is reversed	Servo travel is reversed at the transmitter	Set the transmitter servo reversing switch to the correct position
	Motor wires are not connected properly	Check all motor wires for correct polarity and secure connection
ESC ON – No motor function, audible tone or LED	Battery/connection issue	Recharge/replace battery. Secure all connections
	Damaged ESC	Repair/replace ESC
	Damaged motor	Repair/replace
Motor- Stops and LED blinks	Low voltage protection	When the ESC LED blinks, recharge/replace battery
	Overheat protection	When the LED blinks, let motor/ESC cool, change set up or gearing to avoid overheating
Motor- Accelerates irregularly	Battery issue	Repair damaged wiring/replace battery
	Incorrect gearing	Adjust/replace gearing
	Worn or damaged motor	Repair/replace motor
Motor- Does not turn continuously in response to throttle	ESC/motor damaged	Repair/replace wiring or motor/ESC
Motor- Slows but will not stop	Incorrect transmitter/ESC calibration	Adjust throttle travel/other throttle settings on the transmitter/ESC. Repeat the ESC Calibration Procedure
Steering servo- Operates; motor does not run	Damaged motor	Test the motor apart from the vehicle system, repair/replace motor as needed
	Incorrect transmitter/ESC calibration	Adjust throttle travel/other throttle settings on the transmitter/ESC. Repeat the ESC Calibration Procedure
Steering/motor- not functioning	Low battery voltage	Recharge/replace
	Wrong model memory selected on transmitter	Select correct model settings on your transmitter, refer to transmitter and/or receiver manual
	Receiver not bound to transmitter	Bind transmitter to receiver, refer to transmitter and/or receiver manual
Vehicle- Does not operate at full speed	Battery issue	Recharge/replace
	Incorrect transmitter/ESC calibration	Adjust throttle travel/other throttle settings on the transmitter/ESC. Repeat the ESC Calibration Procedure

LIMITED WARRANTY

What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 2 years from the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions
or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at https://www.horizonhobby.com/content/service-center_renderservice-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole
discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of 1/2 hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website https://www.horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.

WARRANTY AND SERVICE CONTACT INFORMATION

COUNTRY OF PURCHASE	HORIZON HOBBY	CONTACT INFORMATION	ADDRESS
United States of America	Horizon Service Center (Repairs and Repair Requests)	servicecenter.horizonhobby.com/RequestForm/	2904 Research Rd Champaign, IL 61822
	Horizon Product Support (Product Technical Assistance)	[email protected]
		877-504-0233
	Sales	[email protected]
		800-338-4639
European Union	Horizon Technische Service	[email protected]	Hanskampring 9 D 22885 Barsbüttel, Germany
	Sales: Horizon Hobby GmbH	+49 (0) 4121 2655 100

FCC INFORMATION
FCC ID: BRWKATY1T
FCC ID: BRWWACO1T
SUPPLIER’S DECLARATION OF CONFORMITY
Axial SCX10 III Jeep CJ7 RTR (AXI03008)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC
2904 Research Rd.,
Champaign, IL 61822
Email: [email protected]
Web: HorizonHobby.com
IC INFORMATION
CAN ICES-3 (B)/NMB-3(B)
IC: 6157A-KATY1T
IC: 6157A-WACO1T
This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following 2 conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

EU COMPLIANCE STATEMENT:
Axial SCX10 III Jeep CJ-7 RTR (AXI03008)
Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/
EU; RoHS 2 Directive 2011/65/EU; RoHS 3 Directive – Amending 2011/65/ EU Annex II 2015/863.
The full text of the EU declaration of conformity is available at the following internet address: https://www.horizonhobby.com/content/support-render-compliance.
Wireless Frequency Range and Wireless Output Power
Transmitter
2402.0 – 2478.0 MHz
17.7 dBm
Receiver
2402-2478 MHz
3 dBm
EU Manufacturer of Record:
Horizon Hobby, LLC
2904 Research Road
Champaign, IL 61822 USA
EU Importer of Record:
Horizon Hobby, GmbH
Hanskampring 9
22885 Barsbüttel Germany
WEEE NOTICE:
This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

EXPLODED VIEWS

FRONT AXLE

REAR AXLE
TRANSMISSION
CHASSIS
CHASSIS
BODY ASSEMBLY

WHEELS AND TIRES
SHOCK ABSORBERS

PARTS LISTS

Part #	Description
AXI230049	LED Light Set, White/Orange/Red, Early Bronco / Jeep CJ-7: SCX10 III
AXI230053	Body Details Into/Ext CJ-7: SCX10 III
AXI230054	Headlight, Taillight Lens Set CJ-7: SCX10 III
AXI230055	Bumper Set Front, Rear CJ-7: SCX10 III
AXI230056	Cage Set, CJ-7: SCX10 III
AXI230057	Jeep CJ-7 Body Set, Clear: SCX10 III
AXI230058	Rock Slider Left, Right CJ-7: SCX10 III
AXI230059	Doors/Corners/Hinges CJ-7: SCX10 III
AXI230060	Front L/R and Inners Fenders, CJ-7: SCX10 III
AXI231008	Battery Tray Set/Strap: SCX10 III
AXI231009	Upper Center Lnc Mints: SCX10 III
AXI231010	Centre Trans Skid Plate: SCX10 III
AXI231011	Stormont Chassis Brace: SCX10 III
AXI231012	Servo Horn, Metal 23T: SCX10 III
AXI231013	Servo Horn Metal, 25T: SCX10 III
AXI231014	Side Plates & Chassis Brace: SCX10 III
AXI231015	Frame Rail Set: SCX10 III
AXI231016	Bumper/Baymont’s Chs FR/RR:SCX10 II
AXI231017	Shutters& PnhrdMnts Fr/RRSCX10 II
AXI231020	Motor Cover: SCX10 III
AXI231021	Upper Shutter Braces: SCX10 III
AXI231046	Panhead Mount, Sintered Metal: SCX10 III
AXI231048	Servo Mint Brace FR: SCX10 III BC
AXI232002	6-Bolt Differential Locker
AXI232003	6-Bolt Heavy Duty Gear Set
AXI232015B	Slipper Pads Plates: Capra 1.9
AXI232017	Wild Boar Driveshaft Set: UTB
AXI232018	12mm Hex Pin and Spacer (4): UTB
AXI232024	AR45 AxlHsng(Fr)SCX10 III
AXI232025	AR45 AxlHsng (Rr)SCX10 III
AXI232029	Transmission Housing Set: SCX10 III
AXI232030	Motor Mount Plate: SCX10 III
AXI232031	Internal Metal Drive Gears: SCX10 III
AXI232032	Transfer Case Metal Gears: SCX10 III
AXI232033	InputMtlGears 27,20,34T:SCX10 II
AXI232034	40T Metal Spur Gear: SCX10 III
AXI232035	Transmission Shaft Set: SCX10 III
AXI232036	Dig 2-Speed Arm & Shaft Set: SCX10 III

Part #	Description
AXI232037	Cog Set & Plate for Dig 2-Speed: SCX10 III
AXI232044	AR45P AR45 Differential Covers, Black: SCX10 III
AXI232059	AR45 C-Hub (L-R): SCX10 III
AXI232060	AR45 Knuckle (L-R): SCX10 III
AXI232061	AR45 Unvrsl Axles (2): SCX10 III
AXI232062	AR45 Strght Axles (2): SCX10 III
AXI233003	Shock O-Ring Set: UTB
AXI233009	Spring 13x70mm 2.0 lbs/in Ylw(2
AXI233031	Shock Part Composite:SCX10 III BC
AXI233032	Alum Shck Bdy11x39.5:SCX10 III BC
AXI234003	Pvt Ball,Stainless12.75mm(4):UTB
AXI234004	Susp Pvt Ball, Stainless 7.5mm
AXI234006	HD Rod Ends M4 20pcs: UTB
AXI234012	Stainless Steel M6x 88mm Link (2): SCX10 III
AXI234013	Stainless Steel M6x 97mm Link (2): SCX10 III
AXI234015	Stainless Steel M6x 117mm Link (2): SCX10 III
AXI234031	Steering Links Stainless Steel: SCX10 III Std Axle
AXI234033	Panhard Bar and Links, Standard: SCX10 III
AXI234034	Stainless Steel Links, M6 x 105mm (2): SCX10 III
AXI235016	M2.5 x 16mm Cap Head Screw (10)
AXI235098	M2.5 x 8mm Button Head Screw (10)
AXI235099	M2.5 x 10mm Button Head Screw (10)
AXI235102	M2.5 x 18mm Button Head Screw (10)
AXI235109	M3 x 14mm Button Head Screw (10)
AXI235110	M3 x 16mm Button Head Screw (10)
AXI235169	M2.5 x 12mm Flat Head Screw (10)
AXI235174	M3 x 6mm Flat Head Screw (10)
AXI235178	M3 x 14mm Flat Head Screw (10)
AXI236172	Screw Shaft M3 x 2.0 x 12mm
AXI236173	M2.5 x 8mm Pins (6)
AXI237003	4mm x 8mm x 3mm Ball Bearing (2)
AXI43017	1.9 Raceline Daytona Beadlock Wheels, Black (2)
AXI43018	1.9 Mickey Thompson Baja Boss M/T 4.7 R35 Tires(2)
AXIC0005	AXA113 Hex Socket Btn Hd M3x6
AXIC0012	AXA120 Hex Socket Btn Hd M3x25
AXIC0013	AXA013 Cap Hd M2x6mm Blk Oxide
AXIC0015	AXA015 Cap Hd M2x10mm Blk Oxid

Part #	Description
AXIC0114	AXA114 Hex Skt Butn Hd M3x8mm
AXIC0115	AXA115 Hex Skt Butn Head M3x10
AXIC0116	AXA116 Hex Skt Butn Hd M3x12mm
AXIC0118	AXA144 Hex Flt Hd M3x8mm Blk10
AXIC0146	AXA146 Hex Skt Flat Hd M3x12mm
AXIC0147	AXA0147 Hex Skt Flt Hd M3x16mm
AXIC0149	AXA149 Hex Skt Flat Hd M3x20mm
AXIC0218	AXA1218 Bearing 5x10x4mm
AXIC0221	AXA1221 Bearing 5x11x4mm
AXIC0230	AXA1230 Bearing 10x15x4mm
AXIC0291	AXA291 Set Scr M4x4mm Blk Ox(6
AXIC0392	AXA1392 E-clip E2 (10)
AXIC0725	AX30725 Pinion Gear 32p 14t
AXIC1009	AXA0109 Hex Skt Oversize M3x10mm
AXIC1050	AXA150 Hex Skt Flt Hd M3x25mm (10)
AXIC1059	AXA1059 Body Clip 6mm Black(10)
AXIC1120	AX31120 Hex Skt Flat 3x10mm(10)
AXIC1148	AX31148 Wb8-hd Drvshft Coupler
AXIC1180	AXA118 Hex Socket BtnHd M3x18mm(10)
AXIC1243	AXA1243 Bearing 15x21x4mm (2)
AXIC1391	AXA1391 E-Clip E4 (10)
AXIC3066	AX31066 Cap Hd M2x8mm Blk (10)
AXIC3150	AX31250 Ser Nyl Nut Blk 4mm(10)
AXIC4403	AX31403 Bttn Hd Scrw M3x4x10mm (6)
AXIC4406	AX31406 Bearing 7x14x3.5mm (2)
AXIC4407	AX31407 Bearing 5x14x5mm (2)
SPM2340	DX3 SMART DSMR 3CH TX w/SR315
SPMS614	S614 Metal Gear Servo 23T WP
DYNS1216	35-Turn 540 Brushed Motor
SPMXSE1040RX	Firma 40A Brushed Smart 2-in-1 ESC and Receiver
SPMSSX108	SX108 Micro Metal Gear Servo

Part #	Description
DYNB37353	11.1V 3700mAh 3S 50CLiPo 96mmEC3
DYNB5025H3	7.4V 5000mAh 2S50C LiPo, Hardcase: EC3
DYNC2030	Prophet Sport Mini 50W Charger
DYNC3015	P1 Mini AC Balance Char/ Dischar
DYNC3016	Passport P2 2 Port AC/DC MultiCharger
DYNS0900	Brushed Crawler Combo 35T
SPMSS6250	S6250 U-T / H-S Digital HV WP Servo

Part #	Description
SPMSS6280	S6280 U-T / H-S Digital HV WP Servo
SPMX50002S100H3	5000mAh 2S 7.4V Smart 100C; IC3
SPMX50002S30H3	5000mah 2S 7.4V Smart 30C; IC3
SPMX50002S50H3	5000mAh 2S 7.4V Smart 50C; IC3
SPMX50003S100H3	5000mAh 3S 11.1V Smart 100C; IC3
SPMX50003S30H3	5000mah 3S 11.1V Smart 30C; IC3
SPMX50003S50H3	5000mAh 3S 11.1V Smart 50C; IC3
SPMXC2050	Smart S155 AC Charger, 1x55W
SPMXC2080	Smart S1100 AC Charger, 1X100W
SPMXC2000	Smart S2100 DC Charger, 2x100W

OPTIONAL PARTS

Part #	Description
AXI13001	Multi-Color LED Rock Lights with Controller: SCX10 III
AXI230025	Universal Body Post Set: SCX10 III
AXI230031	LED Light Set, White/Red: SCX10 III
AXI231018	Receiver Box: SCX10III
AXI232026	AR45 Differential Cover Red: SCX10 III
AXI233004	Spring, 13x70mm 0.72lbs, Purple Extra Soft (2)
AXI233006	Spring, 13x70mm 1.28 lbs, Red Soft (2)
AXI233013	Spring 13x62mm .78lbs in Purple Super Soft(2)
AXI233016	Spring 13x62mm 1.9lbs in White Medium (2)
AXI330002	Tuff Stuff Overland Accessory Pack
AXI332001	6-Bolt 27 8 Overdrive Gear Set
AXI43001	1/10 KMC Machete 1.9 Wheels, 12mm Hex, Satin Silver (2)
AXI43003	1/10 Method MR307 Hole 1.9 Wheels, 12mm Hex, Satin Silver (2)
AXI43004	1.9 Recline Monster Bead lock Wheels, Black (2)
AXI43005	1/10 MW19 1.9 Bead lock Wheels, 12mm Hex, Gray (2)
AXI43009	1.9 KMC Machete Bead lock Wheels, Satin (2)
AXI43010	1.9 Nitto Trail Grappler 4.74 Wide M/T Tires (2)
AXI43013	1.9 Retro Slot Bead lock Wheels, Satin (2)
AXI43014	Fallen Wild peak 4.7″/1.9″ R35 Tires with Inserts (2)
AXI43015	Black Rhino Primm 1.9″ Wheels, 12mm Hex, Black (2)
AXI43016	1.9 Fallen WILDPEAK M/T 4.19Tir
AXIC0724	Pinion Gear 32P 13T Steel 3mm Motor Shaft
AXIC0725	Pinion Gear 32P 14T Steel 3mm Motor Shaft
AXIC0726	Pinion Gear 32P 15T Steel 3mm Motor Shaft

Part #	Description
AXIC0727	Pinion Gear 32P 16T Steel 3mm Motor Shaft
AXIC1097	3-Port High Output LED Controller
AXIC1143	1/10 Fallen Wild peak R35 1.9 Tire with Inserts (2)
AXIC2014	Gate Marker Set Green Orange (10)
AXIC2016	1/10 Ripsaw R35 Compound 1.9 Tire with Inserts (2)
AXIC2019	1/10 Maxis Toreador Tires R35 1.9 Tire with Inserts (2)
AXIC2020	1/10 Nitto Trail Grappler R35 Compound 1.9 Tire with Inserts (2)
AXIC3070	Universal 5 Bucket Light Bar Set
AXIC3093	1/10 BF Goodrich Krawler T A R35 1.9 Tire with Inserts (2)
AXIC7028	Pinion Gear 32P 17T Steel 3mm Motor Shaft
AXI230025	Uni Body Post Set: SCX10 III
AXI332001	6-Bolt 27/8 Overdrive Gear Set
AXIC0724	AX30724 Pinion Gear 32p 13t
AXIC0725	AX30725 Pinion Gear 32p 14t
AXIC0726	AX30726 Pinion Gr 32p 15t 3mm
AXIC0727	AX30727 Pinion Gear 32p 16t
AXIC7028	AX30728 Pinion Gear 32P 17T
SPMXSE1060	Firma 60ASenseBL Smart Cr ESC
SPMXSEMC08	Firma Sense 1/10 Cr Sys Smart
SPMXSM3001	Firma 2100kv BL Sense Cr Mot
SPMXSM3002	Firma 2800kv BL Sense Cr Mot

facebook.com/axialinc 
instagram.com/axialadventure 
twitter.com/axialrc 
youtube.com/axialvideos

WWW.AXIALADVENTURE.COM
©2023 Horizon Hobby, LLC.
Axial, the Axial logo, SCX10, DSM, DSMR, SLT3, IC3, EC3, Passport, and the Horizon Hobby logo
are trademarks or registered trademarks of Horizon Hobby, LLC.
Dodge, the Dodge grille and related logos, vehicle model names and trade dress are trademarks of FCA US LLC and
used under license by Horizon Hobby, LLC,
©2020 FCA US LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
All other trademarks, service marks and logos are property of their respective owners.
US 9,930,567. US 10,419,970. US 10,849,013. Other patents pending.
Completed 09/23
AXI03008
477827